Brick Paver Installation & Edging



Staging of material

The majority of paver jobs will vary depending upon access, website conditions, project size and naturally, the weather. These scenarios can have an overall influence on your project from a timing stand point. Mindful consideration needs to be taken to figure out the time to start the paver installation. Constantly try to lessen or avoid any traffic on the ready areas.

The supervisor or project supervisor should constantly have the products (sand/ pavers) distributed around the job website for easy and effective setups. Paver pallets/bundles should be put in a way not to disrupt the paver installation. The proper pallet/bundle placement can make the real project installation much easier and quicker by reducing the general labor of managing the material.

Brick paver patterns

Pavers can be put in many different patterns depending on their shape. Each paver shape will usually have several different hatch patterns that are supplied by the manufacturer.

The laying pattern and shape of the paver is extremely important to the performance of the application. Professionals have to take into account the traffic weight loads on their paver tasks. 90 or 45 degree herringbone patterns are recommended in all street and driveway applications, as these patterns will offer the optimum load assistance needed and will resist sneaking from the turning of tires and braking or starting of car traffic. In a lot of applications worldwide, it has been revealed that pavers laid in a herringbone pattern have actually performed properly.

Pavers that are 60 mm (2 - 3/8 in) thickness appropriate for pedestrian applications. Pavers that are going to be utilized in commercial or industrial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a number of conditions that identify the beginning point of a paver task.

When starting to install pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface of the bed linen sand at the ended up elevation of the pavers This will assist as a guide for maintaining straight joint lines and will also enable the installer to make modifications in the positioning of the pavers.

Structures and concrete curbing are typically not straight and ought to not be utilized for developing straight joint lines. The usage of string lines is necessary to figure out the true straightness of the edge. As the paver installation progresses, the string lines will help reduce the requirement for little trim pieces.

These will preserve a minimum joint width and enable the bed linen and jointing sand to get in in between each paver. Pavers with spacer bars are usually not laid in snug versus each other since a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most widely used techniques for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have pulled or above the bedding sand. This will provide you a true and straight line off which to work. When this row is established, you can continue to work outside into the field with the remainder of the pavers. Constantly ensure to regularly inspect your joint lines to make sure they are real and straight. If not, changes to the pavers can be made as you continue setting up. Pavers should be installed hand tight. The best method is to place a paver against another one and let it move down into the bed linen sand. Do not kick or tap the pavers into location as this can toss your lines out of real straightness.

When setting up pavers on a high grade, they need to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

The finest method for setting up pavers on large jobs is to install them mechanically. There are a couple items a contractor need to think about prior to setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in particular patterns.

2.) The specialist must make sure that the producer is capable of production and bundling pavers in the preferred pattern on the pallets for simple mechanical installation.

Poor color mixing might result in a patchy looking installation. The majority of makers are consistent with color mixing on each bundle of pavers, but it is the specialist's obligation to ensure appropriate mixing in Koi Pond Florida the field.

Cutting treatments for brick pavers.

Specialists normally have 2 ways of cutting pavers. When cutting pavers damp, it will assist minimize dust and will prolong the diamond blades life. The operator of the brick saw need to always cut the pavers away from the surface area of the paver field when cutting wet, due to the reality that the pavers will produce a slurry that will stain the paver surface.

The brick saw operator ought to constantly wear the correct defense that is needed for operating a saw, such as eye, ear, breathing and hand protection ).

Edging types

Edge restraints play a significant role in the overall success of an interlocking pavement installation Edging restraints remove lateral movement of the pavers and hold the pavers firmly together. Specifically at the outer border of the paver application, without an edging restraint, your job is guaranteed to stop working gradually.

There are several various edging restraints from which professionals can pick. Typically made edge restraints are the most frequently utilized by specialists. Produced edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone. An edging type that is utilized primarily in industrial and industrial applications is poured-in-place concrete curbs. This edging restraint is normally installed by other professionals.

Edging installation.

This might result in the migration of the bedding sand and ultimate lateral motion of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile material is recommended. When a gap in between the pavers and the edging exceeds 3/8" (10mm), then the space needs to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compacted. The whole area that is to be compacted must be swept tidy of any foreign objects and particles that can trigger scratching or scuffing on the surface of the pavers.

It is very important to have a compactor that can exert between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is necessary that the first compaction occurs prior to any jointing sand has been applied to the pavers. This can trigger a bridging problem and will not enable the joints to be completely filled with jointing sand if jointing sand is applied to the pavers before compaction takes location. This can likewise prevent the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is suggested that you make a minimum of 2 passes in different directions across the pavers. This will enable the pavers to be effectively set in the bedding sand and will force the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really important to the final performance of the pavers. Failure to do appropriate compaction can lead to contortions and pavement failure with time.


Paver pallets/bundles should be placed in a manner not to interfere with the paver installation. One of the most commonly utilized methods for the installation of pavers is hand installation of each paver. The operator of the brick saw ought to constantly cut the pavers away from the surface area of the paver field when cutting damp, due to the fact that the pavers will create a slurry that will stain the paver surface. Edging restraints get rid of lateral motion of the pavers and hold the pavers securely together. When a space in between the pavers and the edging goes beyond 3/8" (10mm), then the space ought to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *